.JPG)
| Application | ||
|---|---|---|
| Spec | ||
| Accelerator Control Cable Bracket Bolts | 89 lb in | |
| Air Conditioning Compressor Bolts | 37 lb ft | |
| Air Conditioning Compressor Bracket Bolts | 37 lb ft | |
| Air Conditioning Idler Pulley Bolt | 37 lb ft | |
| Air Conditioning Tensioner Bolt | 18 lb ft | |
| Air Injection Reaction (AIR) Pipe-to-Exhaust Manifold Bolts | 15 lb ft | |
| Camshaft Retainer Bolts | 18 lb ft | |
| Camshaft Sensor Bolt | 18 lb ft | |
| Camshaft Sprocket Bolts | 26 lb ft | |
| Catalytic Converter Nut | 18 lb ft | |
| Connecting Rod Bolts - First Design (First Pass) | 15 lb ft | |
| Connecting Rod Bolts - First Design (Final Pass) | 60 degrees | |
| Connecting Rod Bolts - Second Design (First Pass) | 15 lb ft | |
| Connecting Rod Bolts - Second Design (Final Pass) | 75 degrees | |
| Coolant Temperature Gauge Sensor | 15 lb ft | |
| Crankshaft Balancer Bolt (Installation Pass-to Ensure the Balancer is Completely Installed) | 240 lb ft | |
| Crankshaft Balancer Bolt (First Pass-Install a NEW Bolt After the Installation Pass and Tighten as Described in the First and Final Passes) | 37 lb ft | |
| Crankshaft Balancer Bolt (Final Pass) | 140 degrees | |
| Crankshaft Bearing Cap Bolts (Inner Bolts-First Pass in Sequence) | 15 lb ft | |
| Crankshaft Bearing Cap Bolts (Inner Bolts-Final Pass in Sequence) | 80 degrees | |
| Crankshaft Bearing Cap Side Bolts | 18 lb ft | |
| Crankshaft Bearing Cap Studs (Outer Studs-First Pass in Sequence) | 15 lb ft | |
| Crankshaft Bearing Cap Studs (Outer Studs-Final Pass in Sequence) | 53 degrees | |
| Crankshaft Oil Deflector Nuts | 18 lb ft | |
| Crankshaft Position Sensor Bolt | 18 lb ft | |
| Cylinder Head Bolts (First Pass all M11 Bolts in Sequence) | 22 lb ft | |
| Cylinder Head Bolts (Second Pass all M11 Bolts in Sequence) | 90 degrees | |
| Cylinder Head Bolts (Final Pass all M11 Bolts in Sequence-Excluding the Medium Length Bolts at the Front and Rear of Each Cylinder Head) | 90 degrees | |
| Cylinder Head Bolts (Final Pass M11 Medium Length Bolts at the Front and Rear of Each Cylinder Head in Sequence) | 50 degrees | |
| Cylinder Head Bolts (M8 Inner Bolts in Sequence) | 22 lb ft | |
| Cylinder Head Coolant Plug | 15 lb ft | |
| Cylinder Head Core Hole Plug | 15 lb ft | |
| Drive Belt Idler Pulley Bolt | 37 lb ft | |
| Drive Belt Tensioner Bolts | 37 lb ft | |
| Engine Block Coolant Drain Plugs | 44 lb ft | |
| Engine Block Heater | 30 lb ft | |
| Engine Block Oil Gallery Plugs | 44 lb ft | |
| Engine Coolant Air Bleed Pipe Bolts and Studs | 106 lb in | |
| Engine Crossmember Bolts (Large) | 107 lb ft | |
| Engine Crossmember Bolts (Small) | 92 lb ft | |
| Engine Flywheel Bolts (First Pass) | 15 lb ft | |
| Engine Flywheel Bolts (Second Pass) | 37 lb ft | |
| Engine Flywheel Bolts (Final Pass) | 74 lb ft | |
| Engine Flywheel-to-Torque Converter Bolts | 44 lb ft | |
| Engine Front Cover Bolts | 18 lb ft | |
| Engine Mount Heat Shield Nuts | 89 lb in | |
| Engine Mount Stud-to-Engine Block | 37 lb ft | |
| Engine Mount Through Bolts | 70 lb ft | |
| Engine Mount Through Bolt Nuts | 59 lb ft | |
| Engine Mount-to-Engine Block Bolts | 37 lb ft | |
| Engine Rear Cover Bolts | 18 lb ft | |
| Engine Service Lift Bracket M10 Bolts | 37 lb ft | |
| Engine Service Lift Bracket M8 Bolt | 18 lb ft | |
| Engine Valley Cover Bolts | 18 lb ft | |
| Engine Wire Harness Clip Bolt | 37 lb ft | |
| Engine Wire Harness Ground Strap Bolt | 37 lb ft | |
| Exhaust Gas Recirculation (EGR) Valve Bolts (First Pass) | 89 lb in | |
| EGR Valve Bolts (Final Pass) | 22 lb ft | |
| EGR Valve Pipe-to-Cylinder Head Bolts | 37 lb ft | |
| EGR Valve Pipe-to-Exhaust Manifold Bolts | 22 lb ft | |
| EGR Valve Pipe-to-Intake Manifold Bolt | 89 lb in | |
| Exhaust Manifold Bolts (First Pass) | 11 lb ft | |
| Exhaust Manifold Bolts (Final Pass) | 18 lb ft | |
| Exhaust Manifold Heat Shield Bolts | 80 lb in | |
| Exhaust Manifold Pipe Nuts | 26 lb ft | |
| Front Shock-to-Engine Crossmember Bolts | 48 lb ft | |
| Fuel Injection Fuel Rail Bolts | 89 lb in | |
| Generator Bracket Bolts | 37 lb ft | |
| Generator Rear Bracket-to-Engine Block Bolt | 18 lb ft | |
| Generator Rear Bracket-to-Generator Bolt | 18 lb ft | |
| Ground Strap Bolt (at Rear of Cylinder Head) | 37 lb ft | |
| Ignition Coil-to-Bracket Bolts | 106 lb in | |
| Ignition Coil Bracket-to-Valve Rocker Arm Cover Bolts | 106 lb in | |
| Intake Manifold Bolts (First Pass in Sequence) | 44 lb in | |
| Intake Manifold Bolts (Final Pass in Sequence) | 89 lb in | |
| Knock Sensors | 15 lb ft | |
| Oil Filter | 22 lb ft | |
| Oil Filter Fitting | 40 lb ft | |
| Oil Level Indicator Tube Bolt | 18 lb ft | |
| Oil Level Sensor | 115 lb in | |
| Oil Pan Baffle Bolts | 106 lb in | |
| Oil Pan Closeout Cover Bolt (Left Side) | 106 lb in | |
| Oil Pan Closeout Cover Bolt (Right Side) | 106 lb in | |
| Oil Pan Cover Bolts | 106 lb in | |
| Oil Pan Drain Plug | 18 lb ft | |
| Oil Pan M8 Bolts (Oil Pan-to-Engine Block and Oil Pan-to-Front Cover) | 18 lb ft | |
| Oil Pan M6 Bolts (Oil Pan-to-Rear Cover) | 106 lb in | |
| Oil Pressure Sensor | 15 lb ft | |
| Oil Pump-to-Engine Block Bolts | 18 lb ft | |
| Oil Pump Cover Bolts | 106 lb in | |
| Oil Pump Relief Valve Plug | 106 lb in | |
| Oil Pump Screen Nuts | 18 lb ft | |
| Oil Pump Screen-to-Oil Pump Bolt | 106 lb in | |
| Oxygen Sensor | 31 lb ft | |
| Positive Crankcase Ventilation (PCV) System Strap Nut (at Right Front Vapor Vent Pipe Stud) | 106 lb in | |
| Power Steering Pump Bolts | 18 lb ft | |
| Power Steering Pump Bracket Bolts | 18 lb ft | |
| Spark Plugs (Cylinder Heads-New) | 15 lb ft | |
| Spark Plugs (all Subsequent Installations) | 11 lb ft | |
| Throttle Body Bolts | 106 lb in | |
| Transmission Housing Bolt | 37 lb ft | |
| Valve Lifter Guide Bolts | 106 lb in | |
| Valve Rocker Arm Bolts | 22 lb ft | |
| Valve Rocker Arm Cover Bolts | 106 lb in | |
| Water Inlet Housing Bolts | 11 lb ft | |
| Water Pump Bolts (First Pass) | 11 lb ft | |
| Water Pump Bolts (Final Pass) | 22 lb ft | |
| Water Pump Cover Bolts | 11 lb ft | |